4″ 150LB Hypalon Fully Lined Diaphragm Valve

Flow Path Design Straight-Through (Non-Weir) ∙ Bore: 85–90% of nominal pipe ID
Size Range DN50 to DN200 (2″ to 8″)
End Connections • Flanged (EN 1092-1 Type A) ∙ ANSI Class 150
• Optional: Lug/Wafer
Flow Coefficient DN100 (4″): Cv ≈ 120 (vs. 180 for full-bore)
Pressure Drop ΔP ≈ 0.3–0.8 bar (water, 2 m/s flow)
Actuation Manual Handwheel ∙ Pneumatic (Spring-Return) ∙ Electric (On/Off)
Certifications PED 2014/68/EU (Cat. II) ∙ ISO 9001 ∙ EN 10204 3.1

문의하기

설명

Straight-Through Diaphragm Valve Technical Datasheet

(Non-Weir, Reduced-Bore Design)
Compliance: BS5156 ∙ 재료: Ductile Iron + Full EPDM Lining

요소	Material & Specification	Key Properties
1. Valve Body	Ductile Iron (EN-GJS-400-18/GGG40) • Full Internal Lining: EPDM (3 mm min. thickness)	• Pressure Rating: PN10/PN16 • Lining Adhesion: ≥ 5 MPa (ISO 4624) • Corrosion Protection: Full EPDM barrier
2. Disc	Ductile Iron (GGG40) • EPDM-Encapsulated	• Reduced-Bore Design: 85–90% of pipe ID • Abrasion-Resistant Surface
3. Stem	AISI 316L Stainless Steel • Mechanically Polished (Ra ≤ 1.6 μm)	• SSC-Resistant (NACE MR0175) • Hardness: 140–180 HB
4. Diaphragm	Hypalon • Polyester Fabric Core	• Temp Range: -20°C to +130°C • Cycle Life: ≥ 50,000 cycles
5. Bonnet	Ductile Iron + Full EPDM Lining	• Bolted Design (EPDM-Coated Bolts)
6. Seals	EPDM O-Rings/Gaskets	• Bubble-Tight Shutoff (ISO 5208 Rate A)

Critical Technical Data

매개변수	사양
Flow Path Design	Straight-Through (Non-Weir) ∙ Bore: 85–90% of nominal pipe ID
Size Range	DN50 to DN200 (2″ to 8″)
End Connections	• Flanged (EN 1092-1 Type A) ∙ ANSI Class 150 • Optional: Lug/Wafer
Flow Coefficient	DN100 (4″): Cv ≈ 120 (vs. 180 for full-bore)
Pressure Drop	ΔP ≈ 0.3–0.8 bar (water, 2 m/s flow)
작동	Manual Handwheel ∙ Pneumatic (Spring-Return) ∙ Electric (On/Off)
Certifications	PED 2014/68/EU (Cat. II) ∙ ISO 9001 ∙ EN 10204 3.1

Straight-Through vs. Full Bore: Key Differences

Feature	Straight-Through Valve	Full-Bore Valve
Bore Diameter	85–95% of pipe ID	100% of pipe ID
Flow Efficiency	Moderate (Cv ≈ 65% of full-bore)	Maximum (No restriction)
Slurry Handling	Good (Less clogging than weir-type)	Excellent (Zero clogging risk)
Mechanical Strength	Higher (Thicker walls due to reduced bore)	Lower (Thinner walls to match pipe ID)
Cost	Lower (Less material)	Higher

Design Advantages of Straight-Through Configuration

Optimized for Slurries & Viscous Fluids

Smooth, obstruction-free flow path prevents particle buildup (e.g., wastewater sludge, pulp).

Robust Pressure Containment

Thicker ductile iron walls (enabled by reduced bore) withstand surge pressures up to 1.5×PN.

Simplified Maintenance

Top-entry diaphragm replacement (no pipe disassembly).

Cost-Effective Corrosion Protection

Full EPDM lining isolates ductile iron from corrosive media (pH 3–12).

Limitations & Design Notes

Not Pigable: Reduced bore prevents pipeline pigging.
Chemical Limits: EPDM incompatible with oils, aromatics, concentrated acids (>20% H₂SO₄).
온도: Max. 130°C (EPDM) – derate pressure above 80°C.
Actuator Sizing: Higher torque required vs. weir-type due to larger diaphragm area.

보증:

SAVVY VALVES는 탁월한 제품 품질과 안심할 수 있는 애프터서비스를 제공하기 위해 최선을 다하고 있습니다. 당사 밸브는 최소 12개월의 서비스 수명을 보장하며, 이 기간 동안 필요한 모든 예비 부품과 자세한 유지보수 지침을 무상으로 제공합니다. 보증 기간 내에 인위적인 손상이 아닌 다른 원인으로 인한 손상이 발생할 경우, 무상으로 부품을 교체하고 전문 기술 지원을 제공합니다. 보증 기간이 만료된 후에는 예비 부품 비용만 지불하시면 되며, 할인된 유지보수 서비스 혜택도 누리실 수 있습니다. 당사의 목표는 신뢰할 수 있는 품질과 포괄적인 애프터서비스를 통해 고객의 운영 비용을 절감하고 생산 효율성을 향상시키는 것입니다. 기술 문의나 유지보수가 필요하시면 언제든지 전문가 팀이 신속하게 대응하여 밸브 시스템이 항상 최적의 성능을 유지하도록 보장합니다.