12″ * 10″-600LB Open Die Forged Choke Valve

Valve Type Needle / Choke Type Throttling Valve (Globe pattern or Angle pattern)
End Connection Flanged, Raised Face (RF)
Body Manufacturing Process Open Die Forging (Free Forging)
Nominal Size NPS 12 × 10 (DN300 × DN250)
Port Reduction Inlet 12″, Internal seat bore reduced to 10″
Pressure Class Class 600 (ASME B16.5)
Body Material A105 (Carbon Steel)
Service Medium Water / Oil / Gas / Steam (as per process)

문의하기

설명

TECHNICAL DATA SHEET

Free Forged Throttling Valve / Choke Valve

Project / Equipment: High Pressure Throttling Valve

BASIC VALVE INFORMATION

Item	사양
밸브 유형	Needle / Choke Type Throttling Valve (Globe pattern or Angle pattern)
End Connection	Flanged, Raised Face (RF)
Body Manufacturing Process	Open Die Forging (Free Forging)
공칭 크기	NPS 12 × 10 (DN300 × DN250)
Port Reduction	Inlet 12″, Internal seat bore reduced to 10″
Pressure Class	Class 600 (ASME B16.5)
본체 재질	A105 (Carbon Steel)
Service Medium	Water / Oil / Gas / Steam (as per process)

APPLICABLE CODES & STANDARDS

기준	설명
API 6A	Specification for Wellhead and Christmas Tree Equipment (if applicable to choke design)
API 6D	Specification for Pipeline and Piping Valves
ASME B16.34	Valve Flange, Threaded, and Welding End Dimensions
ASME B16.5	Pipe Flanges and Flanged Fittings (Class 600 RF)
ASME B16.10	Face-to-Face and End-to-End Dimensions of Valves
API 598 / ISO 5208	Valve Inspection and Testing
ASTM A105 / ASME SA-105	Forgings, Carbon Steel, for Piping Components

MATERIALS OF CONSTRUCTION

요소	재료	Standard / Remarks
몸	A105	Open die forged, normalized
Bonnet / Cover	A105	Forged, bolted bonnet design
Disc / Plug / Needle	A105 + Hardfacing	Stellite 6 / 13Cr – erosion resistant
Seat Ring	A105 + Hardfacing	Integral or renewable, hardfaced sealing surface
줄기	A182 F6a (13Cr)	Stainless steel, anti-galling
Packing	Flexible Graphite	With Inconel wire reinforcement
Gasket	Spiral Wound	304SS + Graphite
Stud Bolts	A193 B7	High strength alloy steel
Nuts	A194 2H	Carbon steel

DESIGN & PERFORMANCE CHARACTERISTICS

매개변수	사양
Pressure Class	Class 600
Max. Allowable Working Pressure	Per ASME B16.34, A105 @ 38°C: ~ 1480 psi (102 bar)
Design Temperature Range	-29°C to +425°C (-20°F to +800°F)
Flow Characteristic	Linear / Equal Percentage
Seat Leakage Rate	Class IV or Class V per FCI 70-2 / IEC 60534
작업	Handwheel / Gearbox / Actuator ready
Flow Direction	Flow over seat (preferred) or Flow under seat

DIMENSIONS & CONNECTIONS

Item	Dimension (inch / mm)
Inlet Flange	12″ Class 600 RF per ASME B16.5
Outlet Flange	12″ Class 600 RF per ASME B16.5
Face-to-Face Length	Per API 6D / ASME B16.10 or manufacturer standard
Reduced Bore Diameter	Corresponding to NPS 10 (approx. 10″ seat bore)
Handwheel Diameter	As per manufacturer
Approx. Weight	As per manufacturer

SPECIAL REQUIREMENTS & REMARKS

Free Forging Process
Valve body shall be manufactured from open die forging using ingot or large billet.
Machining from bar stock or casting is NOT acceptable.
Reduced Port Design
Flange size: NPS 12
Internal seat bore and throttling area: Equivalent to NPS 10
Designed for precise pressure and flow control.
Hardfacing & Wear Resistance
Seat and disc contact surfaces shall be hardfaced with Stellite 6 or equivalent.
Minimum hardness after welding: 350–450 HB.
Nondestructive Examination (NDE)
Body forging to be ultrasonically tested per ASTM A388.
Critical areas (seat, bore, welds) to be MT or PT examined.
Compliance
Valve design, materials, and testing to fully comply with API 6A (if choke valve) and API 6D (pipeline valve) requirements.

보증:

SAVVY VALVES는 탁월한 제품 품질과 안심할 수 있는 애프터서비스를 제공하기 위해 최선을 다하고 있습니다. 당사 밸브는 최소 12개월의 서비스 수명을 보장하며, 이 기간 동안 필요한 모든 예비 부품과 자세한 유지보수 지침을 무상으로 제공합니다. 보증 기간 내에 인위적인 손상이 아닌 다른 원인으로 인한 손상이 발생할 경우, 무상으로 부품을 교체하고 전문 기술 지원을 제공합니다. 보증 기간이 만료된 후에는 예비 부품 비용만 지불하시면 되며, 할인된 유지보수 서비스 혜택도 누리실 수 있습니다. 당사의 목표는 신뢰할 수 있는 품질과 포괄적인 애프터서비스를 통해 고객의 운영 비용을 절감하고 생산 효율성을 향상시키는 것입니다. 기술 문의나 유지보수가 필요하시면 언제든지 전문가 팀이 신속하게 대응하여 밸브 시스템이 항상 최적의 성능을 유지하도록 보장합니다.